World-Link Communications
Starlink Satellite Internet
Enjoy uninterrupted internet access in remote areas with Starlink’s satellite technology.
Fast Starlink Internet Services -
Access & Security Solutions
Starlink uses a constellation of low Earth orbit (LEO) satellites (~540 km up), providing significantly lower latency (20–40 ms) and higher speeds (typically 100–200 Mbps) compared to traditional geostationary systems.
Starlink Mini Kit
Compact and portable satellite internet kit perfect for on-the-go connectivity.
Fast Starlink Internet Services
High-speed internet with access & security solutions for all your needs.
Low Earth Orbit Satellites
Constellation of LEO satellites (~540 km up) providing lower latency and higher speeds.
Performance: Speed & Latency Reality Check
Typical Speeds
100–200 Mbps
Latency
20–40 ms
Max Speeds
100–300 Mbps
Latency Range
30–60 ms
Important Notes
- • Occasional spikes—switching satellites can briefly increase latency to ~150 ms
User Experience
- • Great for gaming, streaming, and video calls
- • Some note intermittent disconnections, weather interruptions, or congestion
Starlink Mini Kit
AC Dual‑Band
Starlink 4th‑Gen Mini Kit
How to Set up
Satellite Home Internet
Setting up Satellite Home Internet in the USA is straightforward, especially with providers like Starlink, Viasat, and HughesNet. Here’s a complete guide to get started.
Starlink Setup (Typical for Home)
Starlink Dish (aka “Dishy”)
Mounting base
Wi-Fi router
75-ft cable & Power cable
Step-by-Step Setup
Create an Account
Go to starlink.com and enter your address. Place the order (hardware ~$599, service ~$120/month).
Install the Dish
Find a clear view of the sky (roof, pole, yard). Use the Starlink app to scan for obstructions. Mount the dish using included base or an optional roof/pole mount.
Connect the Cables
Plug the dish into the router with the included cable. Plug the router into power.
Activate & Configure Wi-Fi
Use the Starlink app (iOS/Android) to name your network and set a password. Wait 5–20 minutes for the dish to auto-align and connect to satellites.
Test Internet
Speed test: Expect 50–200 Mbps. Ping: 20–40 ms. Works with streaming, Zoom, even online gaming (some latency spikes possible).
Common Starlink Installation Errors & Fixes
No Connection / “Searching” Message
Cause: Dish can't connect to satellites due to obstructions or poor positioning.
Fix: Use the Starlink app's 'Check for Obstructions' tool. Relocate dish to a spot with 360° clear sky view. Avoid trees, poles, buildings—even small obstructions cause drops.
Starlink App Shows “Offline”
Cause: Dish is powered but not connecting, or cable is loose.
Fix: Check power supply (router + dish connection). Re-seat both ends of the dish cable (in dish and router). Restart the router (unplug for 15 seconds, then plug back in).
Router Blinking White or Amber Light
Cause: Blinking white: Connecting to satellites. Amber: Firmware updating.
Fix: Wait up to 20 minutes after powering up. If it stays stuck, restart the whole system: unplug everything for 1 minute, then reconnect.
"Starlink Disconnected" in App
Cause: Cable not fully inserted, bent pins, or frayed wires.
Fix: Ensure the cable from the dish to the router is fully inserted. Inspect for bent pins or frayed wires. Try another power outlet or test with a known-good USB-C charger (for Starlink Mini).
Slow or No Internet Despite Good Signal
Cause: Obstructions, network congestion, or firmware needs update.
Fix: Use the app to verify signal quality. Restart the system via the Starlink app → Settings → Reboot. Let it run for 24 hours to auto-update firmware.
When to Contact Support
Reach out to Starlink Support if:
Router shows solid red light (hardware issue)
App says “Motors stuck” or “Thermal Shutdown”
Dish not physically moving during setup
Cable visibly damaged or frayed